Used Volvo FH truck 500 - FALKOM FAW 25.000 - !! Viewing by appointment only !! 8x4 Diesel Euro 6

• 2 Bedden
• Adaptive Cruise Control
• Cabinezijfenders
• Climate Control (ATC)
• Elektrisch spiegels
• Koelkast
• Lane Change Support
• Oliekoeler
• SMART TACHO 2
• Standkachel
• Verstralers op het dak
• Volvo Dynamic Steering
• WhatsApp See no.
• Zwaailampen

Falkom wrecker installation type FAW 25.000
- One main arm.
- A two-stage hydraulically extendable lift arm, very low; Highest step forearm 195 mm, arm length to center bus frame 4.55 m.
- A fully hydraulic installation consisting of:
- hoses
- couplings
- pipes
- 8-function valve block
- Two double-acting lifting cylinders take care of the up and down movement of the main arm.
- The installation is also executed with a so-called "Powertilt" installation to minimize damage to spoilers e.d.
- The assembly is assembled on a subframe, etc. in accordance with specifications of the truck chassis and sprayed in the primer (RAL 2004).
- 2 anchors model working independently of each other standard.
- A lift beam (100 x 100 mm tube).
- Three sets of fork holders.
- 4 sets of V forks.
- 1 Set of chain forks.
- 1 Set of euro forks (German version 1 set of euro forks model small and 3 set for axle forks).
- Set of Scania claws with mounting brackets on the lift beam.
- Set of air suspension forks.
- 1 bus frame.
- Tow bar mounted.
- Shovel and broom mounted.
- Oil tank.
- Pulling device with trawler in combination with a semi-trailer link.
- Supported drawbar coupling support.
- Two 20 ton hydraulic winches (Sepson H 200), which are equipped with two speeds and a pneumatic freewheel.
- Hydraulic double pump.
- Radio remote control for all functions, excluding anchor shovels
- Complete installation is stacked / metallized.
- Built according to CE guidelines.
- Assembly of the air hands and electrical connections of the truck at the rear in the body.
- Luxury enclosure in aluminum version highly adapted to the 8x4 chassis incl. fly-over, mounting the standard forks in the enclosure, LED cabinet lighting, installation installation on the chassis.
- LED light bar mounted on the flyer.
- Lighting control switches mounted in the control box and in the cabin.
- LED flash lamps mounted at the rear.
- 6 work lights mounted (under the flyer, high at the rear and low).
- LED lamps mounted on the corners of the enclosure.
- Starting aid 12/24 volts.
- Air reel mounted.
- Spray the installation in finish.
- 7-wire electrical cable reel installed.
- Container for counterweight mounted behind the cab.
- Base plate for lateral stability (standard legs only)
- 2 fork raisers
- 2 pieces of anchor plates for Wheel chocks
- Two WLL 15 tonne folding discs
- European approved buffer beam at the rear.
- Pulling device with pin 40, 50 and 60 mm
- 2 models towing eyes.
- RDW inspection and, if necessary, TüV.
- Ballast under the bumper.

Cab: Globetrotter, single
Axle 1: Tyre size: 385/65 R22.5; Max. axle load: 9000 kg; Steering
Axle 2: Tyre size: 385/65 R22.5; Max. axle load: 9000 kg; Steering
Axle 3: Tyre size: 315/70 R22.5; Differential lock; Max. axle load: 9500 kg; Reduction: hub reduction
Axle 4: Tyre size: 315/70 R22.5; Differential lock; Max. axle load: 9500 kg; Reduction: hub reduction
Registration number: 28-BPD-3

• Adaptive Cruise Control
• Kühlschrank
• Standheizung

Kabine: Globetrotter, einfach
Achse 1: Reifenmaß: 385/65 R22.5; Max. Achslast: 9000 kg; Gelenkt
Achse 2: Reifenmaß: 385/65 R22.5; Max. Achslast: 9000 kg; Gelenkt
Achse 3: Reifenmaß: 315/70 R22.5; Differenzialsperre; Max. Achslast: 9500 kg; Reduzierung: Ausenplanetenachsen
Achse 4: Reifenmaß: 315/70 R22.5; Differenzialsperre; Max. Achslast: 9500 kg; Reduzierung: Ausenplanetenachsen
Kennzeichen: 28-BPD-3

• 2 Bedden
• Adaptive Cruise Control
• Cabinezijfenders
• Climate Control (ATC)
• Elektrisch spiegels
• Koelkast
• Lane Change Support
• Oliekoeler
• SMART TACHO 2
• Standkachel
• Verstralers op het dak
• Volvo Dynamic Steering
• WhatsApp See no.
• Zwaailampen

Falkom wrecker installation type FAW 25.000
- One main arm.
- A two-stage hydraulically extendable lift arm, very low; Highest step forearm 195 mm, arm length to center bus frame 4.55 m.
- A fully hydraulic installation consisting of:
- hoses
- couplings
- pipes
- 8-function valve block
- Two double-acting lifting cylinders take care of the up and down movement of the main arm.
- The installation is also executed with a so-called "Powertilt" installation to minimize damage to spoilers e.d.
- The assembly is assembled on a subframe, etc. in accordance with specifications of the truck chassis and sprayed in the primer (RAL 2004).
- 2 anchors model working independently of each other standard.
- A lift beam (100 x 100 mm tube).
- Three sets of fork holders.
- 4 sets of V forks.
- 1 Set of chain forks.
- 1 Set of euro forks (German version 1 set of euro forks model small and 3 set for axle forks).
- Set of Scania claws with mounting brackets on the lift beam.
- Set of air suspension forks.
- 1 bus frame.
- Tow bar mounted.
- Shovel and broom mounted.
- Oil tank.
- Pulling device with trawler in combination with a semi-trailer link.
- Supported drawbar coupling support.
- Two 20 ton hydraulic winches (Sepson H 200), which are equipped with two speeds and a pneumatic freewheel.
- Hydraulic double pump.
- Radio remote control for all functions, excluding anchor shovels
- Complete installation is stacked / metallized.
- Built according to CE guidelines.
- Assembly of the air hands and electrical connections of the truck at the rear in the body.
- Luxury enclosure in aluminum version highly adapted to the 8x4 chassis incl. fly-over, mounting the standard forks in the enclosure, LED cabinet lighting, installation installation on the chassis.
- LED light bar mounted on the flyer.
- Lighting control switches mounted in the control box and in the cabin.
- LED flash lamps mounted at the rear.
- 6 work lights mounted (under the flyer, high at the rear and low).
- LED lamps mounted on the corners of the enclosure.
- Starting aid 12/24 volts.
- Air reel mounted.
- Spray the installation in finish.
- 7-wire electrical cable reel installed.
- Container for counterweight mounted behind the cab.
- Base plate for lateral stability (standard legs only)
- 2 fork raisers
- 2 pieces of anchor plates for Wheel chocks
- Two WLL 15 tonne folding discs
- European approved buffer beam at the rear.
- Pulling device with pin 40, 50 and 60 mm
- 2 models towing eyes.
- RDW inspection and, if necessary, TüV.
- Ballast under the bumper.

Cabine: Globetrotter, enkel
As 1: Bandenmaat: 385/65 R22.5; Max. aslast: 9000 kg; Meesturend
As 2: Bandenmaat: 385/65 R22.5; Max. aslast: 9000 kg; Meesturend
As 3: Bandenmaat: 315/70 R22.5; Differentieelslot; Max. aslast: 9500 kg; Reductie: naafreductie
As 4: Bandenmaat: 315/70 R22.5; Differentieelslot; Max. aslast: 9500 kg; Reductie: naafreductie
Kenteken: 28-BPD-3